Mini MH-SR602 SR602 PIR Infrared Motion Sensor Detector Module For Arduino DIY

Description

Home
Electronic Component
Chips
Sensor
Arduino Module
Raspberry Pi
Mini MH-SR602 SR602 PIR Infrared Motion Sensor Detector Module For Arduino DIY
Popular
Popular
Product Introduction
Operating parameters:
Human body pyroelectric infrared sensor module, Model: SR-602
Response distance: up to 5 m; 0-3.5 m recommended
Output: high level, H = 3.3 V, L = 0 V
DC power supply: 3.3 V-15 V
Quiescent current: 20uA
Features and uses:
This module has high sensitivity, fast response, small static power consumption, small size, easy to install and install.
The lens, pin connector was soldered, and the power supply is provided without debugging. Can be used to illuminate the body sensor, alarm, security,
Access control on request, automatic equipment for agriculture, forestry and mining.
Key points:
1. high output time of this product is adjustable, from 2.5 seconds to 1 hour, the output time at the factory.
It is 2.5 seconds and you can change one chip resistor if you need to change it. Please read the resistance value corresponding to the typical delay time.
See Related Form below.
2. blocking time, 2 seconds, is not adjustable.
3. A plant is defined as a repeatable trigger and cannot be changed.
4. The power supply voltage of this module is from 3.3 V to 15 V in, and the limiting voltage is from 2.8 V to 18 V.
5. Module output time: high output within 2 seconds after power on, then go low, enter standby mode
Status. If the delay time is changed, the time when the module outputs a high level after power on will increase accordingly, which can be understood as
Startup time after entering the normal operating state after increasing the electrical power.
6. After installing the Photosensitive element, it does not work during the day, works at night, does not contain photosensitive components, and works all day (There are no photodiodes on the module, if necessary, purchase separately. Recommended: a regular F3 photodiode)
It is believed that the photosensitive element is not installed.
7. This module is very sensitive, pay attention to the installation position, try to avoid the source of heat radiation (air outlet / direct sunlight)
8. The sensitivity of this module is adjustable, and you must change the chip resistor. Please see the table below for details.
Grid.
9. When soldering with a conventional 220 V soldering iron, it is necessary to disconnect the power source before welding. It is recommended to use
24 V low voltage soldering iron, such as 936 internal white light.
10. If you follow the MCU and connect the lamp, please read the control circuit diagram below.
Adjustment time delay instructions
This module can achieve various delays by changing the delay time to adjust the resistance of the resistor.
Time.
The default delay for this module is 2.5 s.
The above table is the data measured by the laboratory and having one
The indicated error is only a reference to the range of debug time.
If you need to change the delay time, please combine, in case of actual use, select the appropriate parameters after debugging a specific circuit.
Control scheme of testing and application
Package Included:
1xMH-SR602 Mini Motion Sensor Detector Module
Payment
Shipping
Refund
Payment
We accept PayPal only.
But we only
Accept
your
Ebay Address
,Please Make sure it's 100% right.
Payment must be received in 5 business days of auction closing.
Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
Shipping
We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
Refund
All package need to
wait 30 days
(US only n
eed 7-10 days)
,
Please take care it.Less than 30 days,we can't take a refund
.
If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it.
If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.